用直流磁控溅射法制备透明导电锡掺杂氧化铟(ITO)薄膜,靶材为ITO陶瓷靶,组分为m(In2O3):m(SnO2 )=9:1。运用分光光度计、四探针测试仪研究了基底温度对薄膜透过率、电阻率的影响,并用X射线衍射(XRD)仪对薄膜进行结构分析。计算了晶面间距和晶粒尺寸,分析了薄膜的力学性质。实验结果表明,在实验设备条件下,直流磁控溅射ITO陶瓷靶制备ITO薄膜时,适当的基底温度(200 ℃)能在保证薄膜85％以上高可见光透过率下,获得最低的电阻率,即基底温度有个最佳值。薄膜的结晶度随着基底温度的提高而提高。

精确的光学常数对于设计和制备高品质的光学薄膜非常重要,尤其是那些光学性能对折射率变化敏感的薄膜。SiO2是一种常用的低折射率材料,因与常用基底折射率相近使其准确拟合有一定难度。实验通过离子束溅射制备了SiO2单层膜。考虑测量时的误差和基底折射率的影响,采用透射率包络和反射率包络得到了SiO2的折射率,并用所得折射率进行反演来对这两种途径在实际测量拟合过程中的准确性进行比对。分析表明,剩余反射率在实际的测量过程中误差更小,直接用测量镀膜前后基片的剩余反射率值可以更简便更准确地得到SiO2的折射率,能达到10-2的精度。

Ta2O5 films were prepared with conventional electron beam evaporation and annealed in O2 at 673 K for 12 h. Laser-induced damage thresholds (LIDTs) of the films were performed at 532 and 1064 nm in 1-on-1 regime firstly, and then were performed at 532, 800, and 1064 nm in n-on-1 regime, respectively. The results showed that the LIDTs in n-on-1 regime were higher than that in 1-on-1 regime at 532 and 1064 nm. In addition, in n-on-1 regime, the LIDT increased with the increase of wavelength. Furthermore, both the optical property and LIDT of Ta2O5 films were influenced by annealing in O2.

A broadband (~176 nm, R>98%, 'lambda'0=800 nm) and high laser-induced damage threshold (LIDT=2.4J/cm2) TiO2/HfO2/SiO2 high reflector (HR) for Ti:sapphire chirped-pulse amplification (CPA) laser system is fabricated by the electron beam evaporation. The refractive index and extinction coefficient of TiO2 and HfO2 films are calculated from single-layer films' transmittance spectra. The properties of HR are mainly determined by the high refractive index material. The high refractive index leads to wide bandwidth. A low extinction coefficient indicates low absorption and high LIDT. The possible damage mechanism of HR is discussed.

The optical property, structure, surface properties (roughness and defect density) and laser-induced damage threshold (LIDT) of TiO2 films deposited by electronic beam (EB) evaporation of TiO2 (rutile), TiO2 (anatase) and TiO2+Ta2O5 composite materials are comparatively studied. All films show the polycrystalline anatase TiO2 structure. The loose sintering state and phase transformation during evaporating TiO2 anatase slice lead to the high surface defect density, roughness and extinction coefficient, and low LIDT of films. The TiO2+Ta2O5 composite films have the lowest extinction coefficient and the highest LIDT among all samples investigated. Guidance of selecting materials for high LIDT laser mirrors is given.